Logo

The reason everyone should own a water butt and how to build one at home

PUBLISHED: 08:32 29 November 2017

You can also fix a butt to sheds, greenhouses and garages - as long as they have guttering

You can also fix a butt to sheds, greenhouses and garages - as long as they have guttering

Philip Toscano/PA Photos

Richard Burr shares his top tips for a DIY rainwater butt

Rain water pipes are usually 65-68mm in diameter for houses in the UK, soil downpipes are 100mmRain water pipes are usually 65-68mm in diameter for houses in the UK, soil downpipes are 100mm

If you’re on a water meter - or you just care about the planet - a water butt is a must for keeping that garden lush and green in the summer months.

They’re easy to fit and if you have the space, you can pop one on each rainwater pipe of your house. Here are my tips for fitting a rainwater butt...

There are lots of pipes outside my house - which ones do I use?

The diverter is the piece of equipment that takes water from the downpipe and channels it into the buttThe diverter is the piece of equipment that takes water from the downpipe and channels it into the butt

It is generally considered good practice to fit most buildings in the UK with roofs! Rain falls on roofs and collects in guttering, which then flows into downpipes and either soaks away in the surrounding ground or is piped away as waste.

Your downpipes are easy to recognise, as, if you look up at your roof, they are connected to your guttering. Do not get them mixed up with your soil pipes (which carry waste from your sinks, baths and toilets and into the sewer) - your water butt will still fill up, but you won’t want to spread the result on your garden.

It's important that the diverter is attached to the downpipe below the top level of your water butt, or once the butt is full with rain, the butt will overflowIt's important that the diverter is attached to the downpipe below the top level of your water butt, or once the butt is full with rain, the butt will overflow

Rain water pipes are usually 65-68mm in diameter for houses in the UK, soil downpipes are 100mm. This guide will show you how to connect to PVC pipes, which are the most common type. If you’re choosing which downpipe to connect to, use one that gets its rain from a large portion of the roof - you won’t fill a water butt up that quickly from a porch roof, for example. But if you want to, you can also fix a butt to sheds, greenhouses and garages - as long as they have guttering.

Kit list you’ll need to build a water butt:

If you're on a water meter - or you just care about the planet - a water butt is a must for keeping that garden lush and green in the summer monthsIf you're on a water meter - or you just care about the planet - a water butt is a must for keeping that garden lush and green in the summer months

A water butt (with stand, to raise it off the ground)

A water butt diverter kit, to match your downpipe

A tape measure

A spirit level

If you're choosing which downpipe to connect to, use one that gets its rain from a large portion of the roofIf you're choosing which downpipe to connect to, use one that gets its rain from a large portion of the roof

A hack saw

A drill with a 25mm bit

A rubber mallet (or block of wood and a hammer)

A concrete paving slab and sharp sand (if fitting on an uneven surface)

Water butts are easy to fit and if you have the space, you can pop one on each rainwater pipe of your houseWater butts are easy to fit and if you have the space, you can pop one on each rainwater pipe of your house

Be sure to raise your butt off the ground

Depending on how much space you have, you can buy water butts that hold various volumes of water, from 25 litres up to over 500 litres. Slim ones are easy to come by and will fit discreetly down a side passage. Most butts will be in the 100-120 litre range and are perfectly adequate. But no matter what sort you get, they need to be mounted on a solid surface and be high enough from the ground to be able to get a watering can or a bucket underneath.

Most water butts have a compatible stand or staging that they come with, otherwise you can easily pick one up. Remember, a litre of water weighs 1kg, so depending on what capacity you buy, your stand will need to potentially carry quite a lot of weight. If you are situating your water butt on an already solid surface, you can place the staging directly onto this. If you are putting the water butt on something less than solid (a flower bed, for example) you’ll need to lay a paving slab nice and level.

To lay a level paving slab, clear away the loose soil where you want your slab to go, loosely spread 50-75mm of sharp sand and gently lay the slab on the sand. Put a spirit level on the slab and tap it down with a rubber mallet (or lump of wood if you don’t have one) until it’s firmly set in place. The connector pipes for water butt diverters are usually 50cm long, so try not to set your butt further away from the downpipe than this.

Fitting the diverter

Once your staging or stand is set, you can plonk (technical term) the water butt on top of it and fit the piping. Your butt will come with a tap fitting, which goes at the bottom and will be fairly easy to screw into place - make sure you tighten it up well, or you’ll have a slow drip that will empty the butt annoyingly quickly.

Now you can fit the diverter. This is the piece of equipment that takes water from the downpipe and channels it into the butt. It’s very important that the diverter is attached to the downpipe below the top level of your water butt, or once the butt is full with rain, the butt will overflow, rather than allowing the water to just continue down the downpipe.

Using your spirit level, mark the top of the rim of your water butt against the downpipe. Measure 3cm down from here and cut through your downpipe with a hack saw (try to make the cut as level as possible). Pull the two ends of downpipe apart and insert the diverter, then push them back into place.

Measure 5cm down from your cut in the downpipe and use the spirit level to mark this on the water butt - this is the height you’ll need to drill the hole in the butt to connect the other end of the diverter. It should say on the diverter packet what diameter drill bit to use, but they are usually around 25mm.

Connect the pipe to the butt, clear up, run back indoors and wait patiently for it to rain. I guarantee that fitting a water butt will give you a frustrating week of perfect weather while you wait for it to fill up. Happy building!

Property search


e.g. Oxford or NW3
Powered by Zoopla

Other Hampstead and Highgate property news

Wasps: a total nuisance or horticultural hero?

They may be the biggest nuisance at summer barbecues, but wasps are also of great benefit to the garden - but how so? A top entomologist reveals all

Seven ways to make sure your dahlias dazzle this summer

As dahlia societies nationwide stage their annual shows this month, expert Katie Kingett offers seven tips to success with these late summer showstoppers

Rug designer Sonya Winner, opens showroom in Dartmouth Park

Emma Rice talks to rug designer Sonya Winner about her passion for colour and her new inspirational showroom in Dartmouth Park

Inside the St John’s Wood home of interior designer, Brian Woulfe

This elegant apartment in St John’s Wood has been carefully curated by interior designer and former concert pianist, Brian Woulfe

House price gap between London and regional cities set to narrow over next two years

The property price gap between London and other cities around the UK is predicted to narrow in the next two years according to figures published by Hometrack

Tom Dixon kicks off series of architecture and design events in Kings Cross

Architecture and design discussion group New London Architecture will be hosting a series of dinners at Spiritland in Kings Cross this summer, starting with an event featuring renowned furniture, lighting and home accessory designer Tom Dixon, on Thursday, July 26.

‘The means of production are changing’ - designer Tom Dixon looks to the future

Tom Dixon, designer of iconic modernist furniture and lighting, has moved his business to a new Kings Cross HQ. Here he talks about what he learned working in the music industry, moving to the epicentre of London’s future industries and finding new creative ‘obsessions’.

New Middle Eastern antiques department opens at Alfies in Lisson Grove

One of London’s last remaining indoor antique markets, Alfies, on Church Street, has launched a dedicated Middle Eastern art, antiques and design department, spanning two floors and more than 4,000 square feet.

Eight ways to get your kids into the garden this summer

As the school holidays beckon, designer Ann-Marie Powell

shares top tips with Hannah Stephen for getting youngsters outdoors

Looking after your lawn: three essential tools

Love your lawn? So, get the right tools to help you maintain it in summer. Hannah Stephenson selects three essentials to make the job easier.

David Walliams is selling Noel Gallagher’s former Belsize Park home

Britain’s Got Talent judge and author David Walliams is selling his Hampstead home for 5.35million with Marcus Parfitt.

Most Read

Newsletter Sign Up

Sign up to the following newsletters:

Sign up to receive our regular email newsletter

Our Privacy Policy


2018 © Archant Community Media Ltd

Terms and conditions | Cookie policy | Jobs at Archant